沿空切顶成巷段巷道围岩变形规律研究

以宏景塔一矿回采工作面为研究对象,基于切顶卸压无煤柱自动成巷技术原理,采用数值模拟计算和现场实测的方法,对该矿成巷段巷道围岩支承压力分布及围岩变形规律进行分析。研究结果表明:随着工作面向前推进,巷道围岩支承压力呈先增大后减小最后趋于稳定的变化趋势,支承压力稳定值为13.5 MPa;受工作面回采动压的影响,距离工作面70 m以内,锚索受力急剧增大到恒阻值、巷道围岩变形明显;距离工作面70~150 m,锚索受力迅速减小、巷道围岩变形逐渐变缓;在距离工作面150 m之后,锚索受力仅有微量变化、巷道围岩变形趋于稳定。因此确定支护体回撤保守安全位置为工作面后方150 m。工程实践表明:所设支护体回撤距离能够应对巷道围岩变形,成巷效果良好。     

输气管道仿真模型校正技术研究进展

为了解决输气管道仿真系统存在计算值与实际值偏差的问题,对解决该问题的模型校正技术展开国内外调研。提出造成仿真计算不精准的三个主要误差来源:输入参数测量误差、缓变参数误差、手工输入误差。最后通过分析国内外仿真模型校正技术研究现状,建议在动态仿真的基础开展输气管道的模型校正技术研究,以避免输气管道系统数据波动带来的误差。     

湿法氧化锌种类和用量对天然橡胶性能的影响

研究湿法氧化锌种类和用量对天然橡胶(NR)性能的影响。结果表明:与添加普通氧化锌的胶料相比,对于未填充炭黑NR体系,减半用量的湿法氧化锌混炼胶的焦烧时间和t90较短,Fmax较大;硫化胶的定伸应力、拉伸强度和剪切模量(G′)较大,拉断伸长率、损耗模量(G″)和损耗因子(tanδ)较小。对于填充炭黑NR体系,减半用量的湿法氧化锌混炼胶的门尼粘度、G′和G″较大,tanδ较小,焦烧时间和t90较短,Fmax较大;硫化胶的密度稍低,硬度和定伸应力较大,耐老化性能较好,玻璃化温度较低,tanδ较小,其他物理性能变化不大。湿法氧化锌FF的性能优于湿法氧化锌HR。     

不同润湿表面液体沸腾的分子动力学模拟

采用分子动力学方法研究纳米尺度下液氩在过热基板上的沸腾过程。通过调节固液间相互作用的方式改变壁面润湿性，模拟并分析了壁面润湿性对沸腾过程中能量传递和液体运动情况的影响。结果表明：不同润湿性表面均会发生固液分离的现象，但是固体表面附近吸附的氩原子数密度随润湿性增强而增大；润湿性较强时，液体的能量上升快，热通量高，液体内部温度梯度大，发生固液分离时间早，系统中氩的温度和能量低，上升过程中液氩密度、厚度变化小；润湿性较弱时，液体的能量上升慢，热通量小，液体内部温度梯度小，发生固液分离时间延后，系统中氩的温度、能量更高，上升过程中液氩密度、厚度变化较大。下部气体压力整体上大于上部气体压力，发生固液分离时润湿性越强的表面上液体上下压差越大，首次上升过程能达到的高度越高，所需时间越短。     

新型实用的动态轨道衡过渡装置

本文通过对GDK-800型不断轨无基坑动态轨道称重装置故障成因的探究,提出对其装置的引轨、防爬和过渡部分,进行优化改造的建议,并简介一种新型实用的过渡装置。     

Design of energy‐efficient train speed profiles considering fixed‐block signaling system

In dense traffic railway networks, trains may often slow down or stop between stations owing to previous train delays. If preceding train trajectory can be predicted, energy‐efficient driving can be achieved by suppressing unnecessary speed changes. In this paper, we propose an algorithm to find energy‐efficient driving considering fixed‐block signaling (FBS) system by using dynamic programming (DP). DP is suitable for use because it can optimize the control inputs with discrete and state constraints. In this paper, we discuss energy‐efficient driving by considering a FBS system using some case studies of simulation. In the simulation, we examine a technique to drive an express train in an energy‐efficient way when the preceding local train is running toward the station with passing loops. The results show that the proposed method can derive complex speed profiles for energy‐efficient driving and the train can be operated with a maximum reduced energy consumption of 8.3%.     

机电控制无级变速器执行机构动态响应特性仿真研究

为研究夹紧力可调的机电控制无级变速器（EMCVT）电控电动执行机构的可靠性，及其速比和从动带轮夹紧力动态响应的影响因素，采用MATLAB/Simulink构建了EMCVT执行机构的动力学模型，设计了针对EMCVT电控电动执行机构的速比和夹紧力闭环控制器。对EMCVT输入转矩突变和目标速比突变两种工况进行了仿真分析，仿真结果表明：速比和从动带轮夹紧力动态响应的超调量和调节时间满足CVT的使用要求，从动带轮夹紧力响应时间小于1s，速比变化率可以达到2；EMCVT速比和从动带轮夹紧力动态响应的主要影响因素是执行电动机的负载和转动方向。     

Asynchronous control for two‐dimensional hidden Markovian jump systems with partly known mode observation conditional probabilities

This study focuses on the asynchronous control problem for two‐dimensional discrete‐time hidden Markovian jump systems where the mode observation conditional probability matrix is partly known. Considering the original system modes are invisible, the observed modes emitted from an observer serve as an alternative for stability analysis and controller design where a mode observation conditional probability matrix is constructed to characterize the emission between system modes and observed modes. Specially, only partly known information of the mode observation conditional probability matrix is accessible. With the introduction of the free‐connection weighting matrices, the asymptotic mean square stability criterion is firstly derived based on Lyapunov method. This introduction provides a further degree of relaxation and less conservatism is therefore achieved. Secondly, we present synthesis conditions for asynchronous state feedback controller design given in terms of a set of interconnected linear matrix inequalities. Moreover, cluster concept based on the partitions of observed modes is adopted which helps to decrease the number of controllers and simplify the design complexity. A numerical example, regarding the cases with and without clustering of the observed modes, is presented to illustrate the effectiveness of the proposed method.